ELECTRICAL - BATTERIES AND ACCESSORIES - BATTERY SWITCHES
(Select from these Groups)
Click pictures to see enlarged view!
WATER-RESISTANT MASTER SWITCH By THE NOCO COMPANY
Excellent for marine or automotive use. Rated 100 amps continuous, 1000 amps surge, at 12 volts; and 50 amps continuous, 500 surge, at 24 volts. 2-1/4" diam. x 2-1/2" deep (1-1/4" deep behind panel). Two 3/16" diam. mounting holes. Extra key and waterproof cover included.

BATTERY MASTER SWITCH By MARINCO RV
Switches can be used as stand alone units, or locked together with other switches. Features a control knob which cannot be removed while in the ON or OFF position, but it can be removed by switching to an anti-clockwise 45° position. Also features removable side plates on 4 sides for access of up to 1/0 cables plus a rear cover insulating the rear terminals against any short circuits. Specifications: •Continuous Rating: 275 Amps DC •Intermittent Rating: 455Amps DC •Cranking Rating: 1250 Amps DC •Voltage Rating: 48 Volts DC •Operation: On/Off •Recessed or Surface Mount •Ignition Protected •Termination Stud Size: 3/8" (2 x 10mm) •Dimensions: 2.75" x 2.75" x 3"H (69 x 69 x 75mm H) •Tin plated copper studs and nuts

HEAVY DUTY MASTER SWITCH By MARINCO RV
Well suited for higher power loads. Can be recessed or surface mounted. Has removable side plates and a rear cover insulating the rear terminals against short circuits. Specifications: •Continuous Rating: 600 A DC •Intermittent Rating: 800 A DC •Cranking Rating: 2500A DC •Voltage Rating: 48V DC •Operation: On/Off •Recessed or surface mount •Ignition Protected •Termination Stud Size: 1/2" (2 x 12mm) •Dimensions: 2.75" x 2.75" x 3"H (102 x 102 x 90mm H) •Tin plated copper studs and nuts

BATTERY MASTER DISCONNECT SWITCHES By JOSEPH POLLAK CORP
Master Disconnect Switches designed for 12 VDC vehicles (Truck, Automotive, Marine, RV) to disconnect all circuitry to reduce possibility of theft and accidental electrical fires. Available in keyed or lever versions, with or without indexing pins, and various sizes of terminal studs. •Lever Operated- 6-36 Volt- 180 Amps continuous capacity 1000 amps in Rush S.P.S.T. (Off-On) Two stud terminals for battery circuit only. Does not disconnect alternator or generator field circuit. On vehicles equipped with alternators, engineer must be shut off to avoid potential damage to alternator diodes. •Incorporates heavy duty contacts. •One piece die-cast housing sealed with O-rings at base and mounting stem to keep out dust and moisture. •Large die-cast, lever for ease of operation. •Two 3/8" copper alloy stud terminals with hex nuts and lock washers. •Overall length 4 3/8". Diameter 2 5/8" approx. •Conforms to requirements of U.L. #558 •Mounting stem 3/4" diameter, l/2" long, with two hexnuts and lock washer. (Note: Mounting nuts not to exceed 12 ft. Ibs. torque). •Designed for protection against battery drain, electrical fires, tampering and theft. •Fits panels up to l/4" thick.

BATTERY SWITCHES By CEQUENT PERFORMANCE
Fits all your needs. 3 terminal for metal frame ground systems, 4 terminal has insulated ground terminal for use with fiberglass or other non-conductive materials. These switches have cadmium plated, non-breakable heavy duty housings. They resist rust, and give long life in most any environment. They isolate the starting battery, assuring you of primary battery power for starting the engine. Has full time charging of both batteries. Includes terminal nuts and lock-washers. For 12VDC continuous duty.