   |
ANCHOR TIE DOWN CORNER By DOCK EDGE
Used to help secure the dock in place if required in rough water conditions. May also replace 86-104-F Corner Plate when extra strength is required. |
|
|
 |
BACKER PLATE By DOCK EDGE
Use on opposite side of all fittings. Prevents pipe from compressing into the wood, resulting in dock sliding down the leg pipe. Also prevents bolts from working into the wood and the lock washers from working loose. |
|
|
|
BACKER PLATE By DOCK EDGE
Use to sandwich the wood framing when another piece of hardware is not used. This prevents the bolts from working into the wood and the lock washers becoming undone. 1/8" galvanized steel plate. |
|
|
 |
BASE PLATE By DOCK EDGE
Used as a footing. It may be bolted to a 2" x 6" piece of lumber and joined to an adjacent leg Base Plate for increased stability. |
|
|
 |
BOTTOM PAD By DOCK EDGE
With its large surface area, this pad is used in soft bottom areas and leg pipe can extend through the pad into lake bottom for extra lateral support. The pointed corners also grab when the bottom is rocky. |
|
|
 |
CHAIN RETAINER By DOCK EDGE
Bolts to side of the dock and uses chain up to 1/2" to secure the dock in place. Use with 99-006-F Washer Plate |
|
|
 |
CONNECTOR HINGE By DOCK EDGE
Used to easily join sections of dock together. Also accommodates joining a fixed ramp to the dock at varying angles. Hinge pin included. |
|
|
|
|
|
|
 |
CORNER LEG BRACE HOLDER By DOCK EDGE
Used when running a 89-101-F Leg Brace Set at right angles from a corner leg to two side legs for optimum stability. One piece per bag with header. Bolts included. |
|
|
|
|
|
|
|
|
 |
GALVALUME LEG PIPE By DOCK EDGE
A heavy wall steel with 10 times the corrosion resistance of normal steel and 2 times the corrosion resistance of hot dipped galvanized steel. 1.9 Gauge/ 1-7/8" O.D. |
|
|
|
|
 |
HD CONNECTOR HINGE By DOCK EDGE
Used at both ends of a ramp when connecting a dock section to shore; where extreme wave action is encountered, or in joining large or multiple sections together where this join could act as a fulcrum or pivot point. |
|
|
 |
HOWELL DOCK FLOATS By DOCK EDGE
•Rotational molded from high density polyurethane with UV inhibitors. Wall thickness is a minimum of 5/16" up to 1/2" at fastening points. •Recessed flanges and center channel allow float to be used on 2' or 4' centers. •1" Drainage plug has sloped channel to eliminate water accumulation around the plug. Water can be added for ballast or to achieve neutral buoyancy •Recessed corners allow clearance for most hardware and nut and bolt heads •Flotation capacity for the Howell 400 is 400 lbs. with overall dimensions of 24" x 48" x 12" high and a tare weight of 28 lbs. Can be shipped UPS |
|
|
 |
INSIDE ANCHOR CORNER By DOCK EDGE
Used in the same applications as a 91-104-F Inside Corner but offers extra strength with its anchor chain bar. Accommodates chain up to 1/8". |
|
|
 |
INSIDE CORNER By DOCK EDGE
Used in lighter duty applications where an outside corner is not necessary. It is also used to replace a 99-002-F Joist Corner in heavy duty applications. |
|
|
|
|
 |
JOIST CORNER By DOCK EDGE
Used to mount stringers with 99-006-F Washer Plates. It can also be used as a backer on the inside edges of the dock to prevent cleats from pulling out. |
|
|
|
|
 |
LEG BRACE HOLDER By DOCK EDGE
Used with 89-101-F Leg Brace Set to connect legs together for maximum stability. One piece, bagged, with header card. Bolts included. |
|
|
 |
LEG BRACE SET By DOCK EDGE
Contains two outer links and one inner link. Extends up to 72" and is used with 93-105-F Leg Brace Holder and/or 87-107-F Corner Leg Brace Holder to connect legs for maximum stability. |
|
|
 |
MALE CORNER HINGE By DOCK EDGE
Used with all styles of Female Connector Hinges. For inside corner support, match with 99-001-F HD Inside Anchor Chain Corner for maximum strength or two 93-122-F Backer Plates. |
|
|
 |
MALE T CONNECTOR By DOCK EDGE
Can be used with all styles of Female Connector Hinges. For inside corner support, match with 92-104-F Inside Corner, 92-116-F Inside Anchor Chain Corner, or 99-001-F HD Inside Anchor Chain Corner. May also be placed anywhere on the side of the dock with a 93-122 Backer Plate for attaching fingers or ramps. |
|
|
 |
OUTSIDE CORNER By DOCK EDGE
Used at outside ends of docks, fingers and swim platforms and in conjunction with either a 99-001-F Inside Corner or 93-122-F Backer Plates, depending on the strength needed. |
|
|
 |
PLASTIC LEG CAPS By DOCK EDGE
Has UV inhibitors. Covers raw leg pipe edges for safety. Also adds a finishing touch to the dock. Packaged 4 pieces in a bag with header card. |
|
|
|
|
|
|
  |
DOCK POST COVERS By IOS
Wave Armor's artfully designed Dock Post Covers are a combination of strength, beauty, and simplicity, featuring a one-piece, weatherproof polyethylene construction. These Dock Post Covers will give your dock impressive beauty with a "completed" look! |
|
|
 |
DOCK WHEELS - AXLE ADAPTER By IOS
Our 2" Dock Post Axle Adapter connects the dock post leg to the dock axle, and easily converts a stationary dock into a portable "roll-in" dock. Designed to be used with a 2" axle and our maintenance-free polyethylene dock wheel. Adaptor features include a heavy gauge, powder-coated steel coupler and stainless steel hardware to prevent rust. |
|
|
 |
MAINTENANCE-FREE DOCK WHEELS By IOS
We are the original manufacturer of "Maintenance-Free Dock Wheel. Our dock wheels are rotational molded using a durable & virtually indestructible polyethylene material, producing a one-piece seamless tire. The heavy-duty construction and wide foot print design allows these wheels to roll over the roughest terrain with ease. The assurance of knowing these tires will never go flat or rust at a great price make them the most popular dock wheels on the market today! Ideal for roll-in docks, boat lifts, and unlimited other uses. •Wheel Dimensions: 25"H x 9" W x 2" axle opening •Sold Per Each |
|
|
