   |
ELECTRIC HYDRAULIC TRANSOM JACKS By T-H MARINE
Gives you the ability to adjust your motor down, while underway at full speed. Ideal for ski, bass or work boats. Designed to fit any standard outboard motor without drilling holes or making modifications in the boat or motor. The motor is set back 5-1/2" from the transom and travels vertically 5". Has no welded parts or aluminum castings to break. Constructed of 1/2" 6061T6 aluminum alloy extrusions and fastened with stainless steel fasteners for maximum strength and durability. The 12VDC self-contained hydraulic power unit is totally waterproof and has a lifting capacity of 7,583 pounds. The motor bracket moves up and down on a transom bracket by use of rollers machined from aluminum-bronze alloy. The jack is available with an optional position indicator gauge which is sealed and drip proof. It is mounted in the dash of the boat. The sending unit is completely sealed and waterproof. |
|
|
 |
MANUAL POWER-LIFT® TRANSOM JACK By T-H MARINE
Totally constructed of 1/2" 6061 T6 extruded aluminum alloy and fastened with stainless steel fasteners for maximum strength and durability. It utilizes an all thread stainless steel screw centrally located for uniform lift, convenience and positive alignment. There are 5" of slot adjustment and 1-1/2" of adjustment at the transom. Designed to fit the standard B.I.A. bolt pattern without drilling holes or making modifications in the boat or motor. Rated for V-6 and smaller motors. •One Piece Design •Centrally Located Adjustment Screw for Convenience & Positive Alignment •5-1/2" Set Back from Transom •5" Vertical Adjustment |
|
|
 |
TWO-PIECE MANUAL TRANSOM JACK By T-H MARINE
The two-piece adjustable manual transom jack has 5" of slot adjustment at the motor mounting bracket and 1-1/2" of adjustment at the transom bracket. After height adjustment has been made, tighten the 4 bolts on the sides to 100 foot pounds to hold the position in place. Motor rating up through V-6. |
|
|
|
|
  |
DETWILER M SERIES MANUAL JACKPLATE By MARINETECH PRODUCTS
Patented Interlocking flat bars for added strength, 300 HP maximum rating, available in 6,8 and 10 inch set-back, ideal for bass boats, aluminum boats, skiff boats, flat boats and off shore racing. Our patented design is the only jack plate that can be adjusted from inside the boat with only one screw. No side hardware to loosen! Just turn the adjustment screw to the desired height, tighten the locking nut, and you are ready to go! •Strong, durable interlocking design •Tongue and Grove design •Anodized aluminum body •Measurement labels •1/2" Aluminum Angle |
|
|
|
|
  |
4 - STROKE BRACKET By MARINETECH PRODUCTS
Adjust your trolling or auxiliary motor to five vertical running positions for changing water or load conditions. The anodized aluminum bracket is built to handle the increased weight and torque output of today's four strokes with long or short shafts. Hand-adjustable with just the turn of a knob, stainless steel torsion springs counterbalance motor weight making adjustments a breeze -- while the 2"-thick, extra-wide mounting board, along with aircraft-type stainless steel hardware deliver heavy-duty performance. |
|
|
 |
4“ SET-BACK PLATE By MARINETECH PRODUCTS
An innovative flared shape allows this four inch set-back bracket more transom contact area to reduce stress and improve the motor's stability. The two piece, T-6 heat treated anodized aluminum bracket will work with even the most powerful main engines. This is an inexpensive solution for lagging performance, while maintaining maximum durability. The pre-drilled hole patterns allow for an extensive range of motor installations. |
|
|
|
|
 |
STATIC MOTOR MOUNT PLATE By MARINETECH PRODUCTS
If trolling motors are your thing - then our static plate is a must. It offers a sturdy and flat mounting area for your trolling motor clamps. When direct to transom motor mounting is difficult, this Plate provides a flat secure mounting surface for clamp-on or bolt-on kicker motors up to 40hp or 150 lbs. |
|
|
  |
ATLAS HYDRAULIC JACK PLATE™ By T-H MARINE
T-H Marine introduces the next generation in jack plate design, built for the heaviest and most powerful V6 engines on the market today, even the big four strokes. Our innovative high tech engineered polymer rod and slot lifting design guarantees trouble free action. This plate also features the newest concept in one-piece hydraulics from the most respected name in hydraulic design, providing the best of all worlds: Speed and Self contained lifting action. This all new pump will lift the heaviest outboard from bottom to top in less than 8 seconds. •Self Contained Hydraulic Pump System - No Reservoir or lines to install •Fast! - Bottom to Top in Less than 8 Seconds •Rod and Slot Lifting Design - Trouble Free Lifting Action •Hi-Tech Engineered Polymer Rods - 6 Times More Abrasion Resistant than Steel •Rods Made from Self Lubricating Material •Easy Two-Pin Pump Removal - Quick Maintenance •Installs in Half the Time of Comparable Jack Plates •Available in 4, 6, 8 10 and 12 inch Setback Models •All V6 - 300hp Max |
|
|
 |
PRO HI-JACKER™ HP By T-H MARINE
"HP" for high performance, this new high strength design jacking plate meets the strenuous requirements of the latest high performance outboards including the toughest four-strokes. Designed with all the features of our popular Pro Hi-Jacker™ series, but from full 1/2" aircraft aluminum stock. Our new "wide side" design adds a full 2" of material to the adjustment slot areas on the side of the plate for additional strength. Will handle all V-6 outboards including the new 4-strokes. •Standard features Include: •Solid one-piece design •Single bolt adjustment from the top •Stainless steel bolts with brass nuts •Locking bars inside for one-wrench adjustment •Full four-inch vertical adjustment |
|
|
 |
PRO HI-JACKER™ JACK PLATE By T-H MARINE
This rugged plate features a solid one-piece design that allows quick and easy adjustment of plate height with the turn of a single bolt from the top. Our unique locking bars inside allow the side locking bolts to be adjusted from the outside with a single wrench. Manufactured from 3/8" aircraft aluminum stock, this plate can handle the stresses from all V-6 outboards up to a max of 175hp. Our new "wide side" design adds a full 2" of material in the adjustment slot area for additional strength. Unit features all stainless hardware with brass nuts to prevent galling. Full four inches of vertical adjustment. |
|
|
 |
Z-LOCK™ MANUAL JACK PLATE By T-H MARINE
Exclusive Z-Lock Design Provides •Maximum Strength •Prevents Side Slippage and Movement •Easily Adjusts Up or Down with Center Bolt •Full 1/2" Aluminum Material for Strength •Handles All V6 Outboards – 300hp Max |
|
|
